What Cinderella left behind

35 days to go...

In the interests of retaining a modicum of sanity I decided to take a few hours off from the dress construction. With time ticking though, I didn't want to abandon the project completely so I made a start on my dance slippers. A few hours relaxing embroidery and I am ready again to tackle the skirts on the silk dress.

During the 1840s, the most common form of women's footwear for dancing and evening wear was a silk or leather slipper. These little shoes are very similar to what we would identify today as a ballet pump.

Shoes worn by Queen Victoria for her wedding - Northampton Museum

Shoes at this period had no right and left foot but were instead made straight. The toe was often stiffened and tended to be much shallower than a modern shoe with a square toe.

Shoes were decorated with ribbons, rosettes and pompoms as well as with intricate embroidery. Women would often embroider shoes as gifts for friends and relatives. However, a dance slipper did not always last a long time. According to some accounts, the fine leather soles could be so thin that a particularly enthusiastic dancer could wear out her shoes by the end of one ball!

Ladies Mid-Nineteenth Century Embroidered Shoe (found here - a brilliant source for a whole range of Victorian footwear styles)

To create my dance shoes I started with an ordinary pair of white leather ballet shoes bought from a dancewear shop. I have worn these previously and they are, unsurprisingly, very easy to dance in! For a more authentic toe shape, dancers' demi-pointe shoes are better as they have a square toe and are stiffened with glue. However, the only pair I have are peach-coloured and leather pumps are more comfortable for dancing.

The shoes - BEFORE

My embroidery design was inspired by these Nineteenth Cenury baby shoes.

To decorate my shoes I used three shades of cotton embroidery floss, tiny green glass seed beads and gold-tone metal sequins which are specifically made to resemble the types of sequin used in historical dress. These are tiny metal discs with a hole pierced in the centre. The edge of the shoe is finished with a gathered strip of fabric to match the ball gown and long ribbons cross over the foot and tie around the ankle.

And ...AFTER...

Other foot to follow very soon!

Bodice Construction - Part II - The sleeves

36 days to go and the sleeves for the silk dress are complete.

Fashions for sleeves changed with amazing rapidity throughout the nineteenth century, veering from one extreme to the other.

At the beginning of the century, gowns tended to feature short, puffed sleeves or long, narrow, fitted sleeves depending on the type of dress.

A fashion plate from 1815 found here

By the 1830s, however, sleeves had achieved quite incredible proportions and were known as "Leg O'Mutton" or "Gigot" sleeves. Indeed they were so large that feather-filled pads were worn around the upper arms to hold out the sleeves! (Click on the image below to find out more about this dress).

Sleeve detail on an 1830s dress in the collections at The Museum at FIT (Fashion Institute of Technology)

By the 1840s, with it almost impossible for sleeves to get any bigger, the reaction was for fashion to swing once more in the other direction. Slimmer, more fitted sleeves began to come back into vogue for day dresses. Evening dresses tended to feature very small, straight sleeves or little puff sleeves.

From "The World of Fashion" periodical, 1845 (found here)

The pendulum continued to swing in this way throughout the rest of the century with sleeves expanding and contracting almost with each decade.

For my 1840s silk gown, I have opted to make the sleeves convertible. Victorian etiquette dictated that during the day the arms and throat must be covered. In the evening, however low cut, short-sleeved gowns were considered both proper and fashionable. It was not uncommon for dresses at this period to be made with two bodices so that the same dress could be worn both during the day and for evening wear. There are also examples of wedding dresses with detachable sleeves and a fill-in for the neckline. This meant that the dress, worn for a morning wedding, could be converted and worn later as a ball gown or evening dress.

Inspired by this, I have cut my sleeves so that the lower sleeve is detachable. During the day, the bodice can be worn with the long sleeves and a chemisette (false blouse) to fill in the neckline.

The upper part of the long sleeve is made from lining material and when this sleeve is used it is loosely tacked (stitched) in place by hand temporarily.

The lower sleeve, showing the top portion of lining fabric that is tacked inside the bodice sleeve head

To transform the dress into an evening gown, the lower half of the sleeve is simply removed.

Just like the original gown that the pattern was taken from, the sleeves are decorated with two simple bands of fabric that form cuffs. These also disguise the join when the long sleeves are added.

Sleeve detail

Bodice Construction - Part I

39 days to go...

Work is progressing well on the silk dress and I thought I would share some of the stages of the bodice construction.

Preparing to cut the fabric

Firstly, I cut all of the dress pieces from both the silk and the lining. It took some time to carefully position the pieces to ensure that the stripes matched where I wanted them to. The darts and curved seams of Victorian patterns make it impossible to match all of the seams but I chose to make sure that the front matched on the diagonal to create a chevron on the centre seam.

Some quick research into original dresses showed this way of using striped fabric to create visual interest was used in the 1840s. Both of these dresses from The Manchester Gallery of Costume feature striped fabrics that have been cut to create a distinctive chevron pattern on the front of the bodice. You can click on the pictures below to find out more about each dress.

 1840s Day Dress, Manchester Gallery of Costume

Tartan Wedding Dress, 1849, Manchester Gallery of Costume

Once all of my pieces had been cut out, I matched all of the silk pieces with the cotton lining. The bodice is flat-lined which means that each lining piece is pinned to the back of its corresponding silk panel. These are then treated and stitched as one piece of fabric. To make them easier to handle you can edge stitch around the pieces to prevent the fabric from moving. However, I chose not to do this as I did not want visible machine stitching even on the inside of the dress. To make the dress more authentic I am hand-stitching the majority of the bodice, including hand-finishing the seams.

Matching silk and lining pieces cut out

Positioning and pinning the lining to the silk

I stitched the front pieces first as there is no piping on the front seams. First of all using the pattern and a tape measure I marked the seam lines for darts (the triangular slits at the front) on the lining side of the fabric. Closing these darts gives the bodice a three-dimensional shape which is slimmer at the waist and shaped to accommodate the bust.

Marking the seam lines for the darts

The darts stitched closed

 Before stitching the rest of the bodice, I then applied piping to the side and back seams. The piping cord is positioned on the outside of the seam line. When the pieces are stitched together, the piping sits on the outside of the seam.

Piping applied to the side back panel

I also turned in and slip-stiched down the facings at the centre back where the bodice will open and close.

Centre back facing slip-stitched to the lining

It was then time to attach all of the pieces together, paying careful attention to matching the stripes at the front and sewing as closely and neatly as possible next to the piping.

The inside of the bodice

The seams are carefully ironed on both sides to press them flat. Curved seams are clipped at intervals to allow them to lie flat. This can be done with a simple snip finishing just before the stitching but I chose to cut out small shaped triangles as this is the technique that I have seen used on curved seams in many original garments. It also creates an attractive seam finish on the inside. All of the raw edges where whip-stitched to finish the edges. This involves taking quick single stitches at a slight angle that loop around the raw edge and help to prevent the fabric from fraying.

Piping on the bottom edge

Finally, the top and bottom edges were finished with piping. On the top edge, the seam allowance of the piping was turned to the inside, folded over and stitched to the lining. However, on the bottom, I have left about 2/8" of fabric below the piping where I will attach the skirt.

In my next post I will share how I have created convertible sleeves which can be worn either long or short to make this dress suitable to wear in the day and in the evening.

The first dress complete - an 1840s striped day dress

43 days to go...

Apologies for the large gap in posting. I got rather carried away over the last few days with completing the first gown for Queen Victoria. This included a few late nights (including one where I found myself still stitching at 4am!) and as a result I haven't managed to squeeze in a post.

But here it is...the first gown.

Note: the neckline is very low so the chemise is currently showing at the neck. When worn, however, the dress will be teamed with a chemise that follows the neckline so that it doesn't poke out like this one does!

Strictly speaking, this dress is, in fact, a test run for the real thing. I will be making a second version of this dress in silk. However, it is always advisable, especially when using an original pattern that has been adapted like this one, to test the fit of the pattern in a cheaper material. Making a toile (a mock up in calico) is a good option, used by top designers in couture fashion, but in this case I also wanted to practise the techniques to ensure that all of the elements of the dress worked as I expected.

I therefore decided to make the dress completely from another fabric to test the fit and construction methods thoroughly before cutting my silk. This is, of course, more time consuming but avoids errors later and, on the plus side, leaves you with another completely wearable dress, unlike the mock-up method. It doesn't have to break the bank either.

The material I used for this dress was the lining of an old curtain. I bought (or should I say my Dad bought for me!) a pair of curtains in a vintage store. They were very large (about 3m squared) and were fully lined, with both the outer fabric and the lining suitable for making costumes. The fabric is a medium weight cotton and very easy to handle. Even better, I only needed the lining of one curtain for this gown so the fabric cost less than £12 which is not bad for a Victorian dress.

I started by constructing the bodice. Before stitching any of the pieces together I had to sew the piping along the seam lines.

Piping applied so that the cord lies just inside the seam line

The pieces were then sewn together, placing the stitches very closely along the edge of the piping cord. This means that the cord then appears of the outside of the garment along the seam lines. It is important for the stitching to be neat and as close to the cording as possible to achieve a neat line. I completed all of this stitching by hand. This allows for a neater finish as you have more control over the material when working by hand. It is also historically authentic as although the sewing machine did exist, it was not yet widely used at this period for making clothing, especially in the home.

Side view of the bodice showing the seam piping

As well as being decorative, this cording helps to emphasise the cut and shape of the bodice. The back seams in particular which sweep up and out from the waist create the illusion of a smaller waist and make the dress appear very wide at the shoulders.

The front of the dress has a deep point at the waist which is typical of this period and the bust area is shaped with long darts. Using the striped material to create chevron down the front of the gown is also something I have seen on original gowns from this period. Both of these features again help the waist to look even smaller than it actually is.

The skirts are attached following the line of the pointed bodice. The skirt fabric is folded to the inside along the top edge, with the fold tapering to a point at the centre front. The material is then cartridge pleated (find out more about cartridge pleating here) and stitched to the dress by hand. The pleating stands out over the hips, creating full skirts and emphasising the waist.

The sleeves also feature piping along both seams. They are cut with a curve that follows the natural curve of the arm. This allows the sleeve to be cut much tighter and still allow the arm to bend. The cuff are finished with piping with a slit at the wrist to allow the hand to pass through and are set into the bodice with a smooth sleeve head (no gathers on the shoulder).

Sleeve detail

All of the techniques worked with no problems so I am now ready to begin work on the silk version of this dress which will feature convertible sleeves to allow the dress to be worn in the day and the evening.

Preparing for piping

46 days to go...

The first dress is finally cut out and ready to go. However, before I could begin construction I had to take account of a very important feature of 1840s dress.

It was customary at this period for most of the bodice seams to be decorated with piping. Piping is when a narrow cord inside a tube of fabric is sandwiched into the seam. This creates a decorative cord along the seam line on the outside of the garment. This is most commonly used to today to finish the edges of cushions.

An example of cushions with piped seams (from here)

In the 1840s, piping was used to add definition and emphasise the seam lines of garments.

V&A_T.32-1940_Day Dress 1836-1840 - This cotton day dress has green contrast piping on all of the bodice seams, with a thicker double piping used to finish the bottom of the bodice.

So before beginning to stitch my bodice I had to prepare several metres of piping. I used a continuous bias strip cut from the fabric (find out how to cut one here). Using the bias (diagonal) of the fabric is important as it allows the piping to stretch and bend easily around curves and corners. This strip was folded in half lengthways and a thin blind cord tightly sewn into the fold.

From left to right: unfolded bias strip, folded bias, blind cord

With the cord sewn in to create the piping

All ready to be applied to the bodice

The next step will be to apply this to all the seams of the bodice prior to construction.

Drafting and resizing an original pattern

48 days to go...

Firstly, apologies for the lateness of this post which can be blamed on the Glasgow Subway replacement bus service. I was home rather later than planned the other evening when a 15 minute journey took an hour and 15 minutes. As a result, I didn't get a chance to upload this post as planned.

In the meantime, work has been progressing well on the pattern for the dress and I thought I would share a little of the process of adapting an original pattern to fit.

To begin with, it is wise to have a number of tools and materials handy.

To scale the pattern up to full size, squared pattern paper is a must. The original pattern is printed on squared paper on 1/8inch squares. I marked my centimetre squared paper with a cross every 2.5cm to get square inches. Then, by counting the squares and replicating the lines of the original pattern in relation to the squares made a full size copy of the pattern.

Next, I took measurements of each of the pieces to figure out the size of the original wearer. I made notes on the flat pattern pieces but the most accurate measurements were made after taping the seams with masking tape to put the pattern together. In 3-D form it was much easier to see exactly where the waist and bust of the garment were and to measure for example the arm scye (armhole).

As suspected, she was a tiny lady compared to today's standards. Not only did she have a 24inch waist but she appears to have been very short from the neck to the waist. On the other hand, her bust was surprisingly big in comparison to her waist measurement. However, portraits from this era do show a very wide, high bust line and the gored corset tends to lift and exaggerate the bust.

Grand Duchess Alexandra Nikolaevna of Russia, Princess of Hesse-Kassel 1840 (image found here) - although probably somewhat exaggerated, this portrait shows the large difference between the bust and waist that was fashionable at this time

Nevertheless, this made altering the pattern to fit something of a challenge. Since the bust was almost big enough but the waist 5 inches too small, this was not simply a case of adding a bigger seam allowance. Furthermore, the arm syces on the original pattern were extremely small, and whilst tight, low set sleeves were a feature in the 1840s, I needed to do something to ensure that I would be able to move my arms.

My first move was to compare my measurements to the pattern and then, using various calculations to determine the ratios and proportions of each section of the pattern, draw up new pattern pieces. The aim was to ensure the each piece of the pattern retained the same proportion in relation to the others whilst being made bigger. Once I had the general shape, I then altered the lines to reflect the fact that the difference between my bust and waist would not be as exaggerated as that of the lady who originally wore the dress. I won't go into too much detail here as this was quite a technical and mathematical process but please ask questions if you would like to find out more.

Some of the notes and calculations!

Once I had the new pattern pieces, I cut these out and taped all of the seams with masking tape. I could then try the paper bodice onto Gertrude, my dress form, over the corset and petticoats. This allowed me to see where the pattern fitted and which areas needed to be adjusted. Any loose areas of paper were pinched into darts and pinned flat. Extra paper was taped to the edges and between panels where the pattern didn't fit and new seam lines and edges drawn on.

Pinning the front - notice the tuck in the side panel below the bust

Adding paper to the shoulder and underarms and drawing new seam lines

Excess paper trimmed away on the new seam lines

Once the pattern fitted Gertrude perfectly, I removed it from the mannequin and cut the pieces apart along the new seam lines. I then drew around these news pieces and added seam allowances to make the pattern pieces I would need to cut the fabric.

Looking like a bodice - the pattern removed from the mannequin

The new pattern pieces

The next stage is to test these pieces in lining fabric with the sleeves before beginning to make up the dress in a test fabric. I will be making a complete dress in cotton fabric salvaged from some old curtains before making this pattern in silk. This will mean I have an extra dress suitable for wearing in less favourable weather conditions (although I have been promised glorious sunshine for the whole week!) and will avoid any mistakes being made with the more expensive silk.

The pattern for the dresses

49 days to go...

Today it was finally time to start work on the dresses themselves. In order to make Victoria's costumes as authentic as possible, I have decided to use a pattern from Janet Arnold's "Patterns of Fashion 1".

This wonderful series of books offers detailed drawing and patterns for original dresses in museum collections around the UK. Careful measurements taken from the garments were used by Arnold to draft patterns that allow us to essentially recreate the real thing. These patterns are complete with detailed annotations on the construction techniques used to put the dresses together.

The dress I have chosen as the basis for my pattern is a day dress in The Gallery of English Costume in Manchester (now The Gallery of Costume). The dress is dated c.1839-1845 and is described as,

"A day dress in a delicate shade of deep beige. The fabric is a silk and cashmere mixture with a soft, glossy finish. The two piece straight sleeves are decorated with double crossway pieces, which are trimmed with piping and bouillons. The neckline would have been edged with lace or worn with a chemisette. The bodice is decorated with flat, pleated folds of the same fabric as the dress. which descend from the shoulder to the centre front." ((Arnold, p64)*

 The only drawback of these patterns is the size. In contrast to commercially available patterns such as Truly Victorian, Laughing Moon and The Mantua Maker, you cannot simply pick your size and happily cut away. Firstly, each dress is unique and the pattern reproduces the exact size of the original wearer - for the most part rather small! Furthermore, the patterns have then been scaled down to 1:8 for printing. A little preparation, calculation and experimentation is therefore required to obtain a usable pattern.

Visit tomorrow to find out more about how I created the bodice pattern for Queen Victoria's gowns using this pattern.

*References
Janet Arnold, Patterns of Fashion 1, Englishwomen's dresses and their construction c.1660-1860,(Macmillan, London, 1977).